topic Publicly Addressable Name in Alfresco Archive

Publicly Addressable Name

freedom20 — Sat, 23 Jan 2016 00:17:21 GMT

Hi,I just installed Alfresco (201510-EA) and after installing it works fine on the Linux server I installed on but I cannot hit it from any other machine on the network. This is in the install document:<blockquote>Use the URL http://127.0.0.1:8080/share on this machine to verify that Alfresc

Re: Publicly Addressable Name

kavilash23 — Mon, 25 Jan 2016 05:57:11 GMT

Hi,

"How do you define and created a publicly addressable name?"
What the above means is that you need a DNS which resolves to the alfresco server ip (assuming you don't have any proxy server sitting in front of the alfresco server) and set it in tomcat/shared/classes/alfresco-global.properties.

alfresco.host and share.host are the ones you need to change.

And make sure port 8080 is opened and accessible on the alfresco server and your firewall.

Re: Publicly Addressable Name

freedom20 — Tue, 26 Jan 2016 15:09:51 GMT

Thank you. I made the changes to the alfresco-global.properties. It still does not work. I'm going to down the road of trying to figure out if port 8080 is open. To my knowledge there is no firewall running. I cannot find that iptables is running and there is no firewall between my workstation and this server.

Re: Publicly Addressable Name

eswbitto — Tue, 26 Jan 2016 20:58:52 GMT

Depending on your operating system you might actually have both iptables and firewalld installed

systemctl iptables status
systemctl firewalld status

They should be dead if you don't want them on.

Re: Publicly Addressable Name

freedom20 — Wed, 27 Jan 2016 00:02:00 GMT

Does anyone have any other hints at what I can look at? I have spent several hours on this and have made no progress.

<blockquote>And make sure port 8080 is opened and accessible on the alfresco server and your firewall. </blockquote>

What all should I check to make sure this is open? When I do a netstat it shows 8080 under TCP6. But when I look by running this "# ip a | grep inet" it does not return any ipv6 addresses. I've also looked in the /opt/alfresco-community/tomcat/conf/server.xml file and cannot find the line "resolveHosts="false"".

I can hit Alfresco Share from the local server just fine I just can't hit Alfresco from any other computer on the network. I can ping the machine by name and have tried the IP address as well.

Thanks

Re: Publicly Addressable Name

freedom20 — Wed, 27 Jan 2016 00:05:50 GMT

Thanks, I hadn't refreshed the page in a while and saw your reply right after my last post. I tried this and received.

"Unknown operation 'iptables'"
"Unknown operation 'firewalld'"

I'm running Oracle Linux 7.

Re: Publicly Addressable Name

freedom20 — Wed, 27 Jan 2016 23:26:18 GMT

Anybody?

I have…

added the ip and hostname to the hosts file

added 'address="0.0.0.0"' and 'useIPVHosts="true"' to the Connector port="8080" section in the /opt/alfresco-community/tomcat/conf/server.xml file

Re: Publicly Addressable Name

eswbitto — Thu, 28 Jan 2016 18:45:46 GMT

Yeah sorry about that…..that was my bad. I typed it down wrong for you.

try

systemctl status firewalld.service
systemctl status iptables.service

Re: Publicly Addressable Name

eswbitto — Thu, 28 Jan 2016 19:03:21 GMT

At a command prompt if you use the command: hostname

Does the server have a hostname setup?

Here is some references you should probably take a look at.

http://www.thegeekstuff.com/2013/10/change-hostname-ip-address/

Re: Publicly Addressable Name

freedom20 — Thu, 28 Jan 2016 22:21:46 GMT

Thanks for your help. That returns "tsserver01.localdomain".

I messed with everything in that article and restarted several times. I also turned off ipv6 in the ifcfg-eth0 file because when I ran netstat -nlp it looked like 8080 was on tcp6 instead of tcp. It got to the point where I could no longer VNC to the machine but I could still Putty to it and ping by name. I removed the entries in the hosts file and then I could VNC to it again. Then Alfresco would no longer work from within the machine. Now 8080 is showing up under tcp instead of tcp6. I turned the IPV6 back on and now I'm back where I started. It works from within the machine but not from another machine.

Re: Publicly Addressable Name

eswbitto — Fri, 29 Jan 2016 17:29:27 GMT

I would try from another machine to ping the server to make sure you have connection. If you can ping then I would almost bet its a firewall (network gateway for all traffic) or proxy server issue.

Re: Publicly Addressable Name

freedom20 — Fri, 19 Feb 2016 00:17:31 GMT

ESWBitto,

I missed your response up earlier in the thread where you corrected the syntax for checking the firewall. Someone pointed that out to me and determined that firewalld was running. Once that was disabled I was able to connect externally. Thanks for all of your help!